- Heating and cooling - Gas Furnaces - YORK

GY8S-E
GY8S-E Model: GY8S-E Capacities: 160 Input MBH 78% AFUE Warranty: Compressor - NA Heat Exchanger - 20 Years Other parts - 5 Years 78% AFUE Mid Efficiency Light Commercial Gas Furnace This mid-high efficiency, compact unit employs induced combustion, reliable hot surface ignition and high heat transfer tubular heat exchangers. The unit is factory shipped for installation in upflow or horizontal applications. This furnace is designed for residential and commercial applications. The unit is factory assembled, wired and tested to assure safe, dependable and economical installation and operation. The unit is Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Easily applied in upflow, horizontal left or horizontal right installation with no conversion necessary. Electronic hot surface ignition with high reliability and dependability. 100% shut off main gas valve for added safety. Rollout safety control Large belt drive blower for high CFM and static capability 1-1/2 HP ball bearing motor. Reliable hot surface ignitor. Aluminized tubular heat exchanger for long term durability. High quality inducer motor for quiet operation. Standard terminals for controlling humidifiers and EAC's or other commercial application requirements. 40 VA control transformer fuse protected. Easy to connect power and control wiring. Efficiency ratings of 78 AFUE attained by using tubular heat exchangers. Cooling relay supplied for easy installation of add-on cooling. Adjustable fan-off settings to eliminate "cold-blow". Equipped with timer relay providing motor protection if operated on continuous blower or if units are "twinned" 208/230v operation, convertible for 115v Model is propane convertible Attractive baked enamel finish for durability.
TG8S / TGLS
TG8S / TGLS Model: TG8S / TGLS Capacities: 40 - 130 Input MBH 80% AFUE Warranty: Compressor - NA Heat Exchanger - 20 Years Other parts - 10-Year Limited* 80% Single-Stage PSC Multi-Position Gas Furnace These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Compact 33” Height and Standard Cabinet Widths. Multi-Position Design With Minimal Conversion Requirements. Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1” ESP. PSC Four-Speed Direct Drive Motor with Large, Quiet Blower. Fully-Supported, Slide-Out Blower Assembly for Easy Service Access. Tubular Aluminized Steel Primary Heat Exchanger. High-Level Self-Diagnostic Controls With Fault Codes. Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal. Fully-Gasketed, Independent Access Doors With View Ports. External Air Filters (Not Included) Provide Flexibility for IAQ Needs. All Models Are Propane Convertible. Lo-Nox Models Meet Specific Code Requirements
TG9S
TG9S Model: TG9S Capacities: 40 - 130 Input MBH 95.5% AFUE Warranty: Compressor - NA Heat Exchanger - Lifetime Other parts - 10-Year Limited* 95.5% AFUE Single-Stage PSC Gas Furnace (TG9S) These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. Designed and certified as Category IV furnaces, these furnaces may be installed as direct vent systems through side wall or roof applications using approved plastic combustion air and vent materials. Special Benefits Compact 33” Height and Standard Cabinet Widths. Multi-Position Design With Minimal Conversion Requirements. Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1” ESP. PSC Four-Speed Direct Drive Motor with Large, Quiet Blower. Fully-Supported, Slide-Out Blower Assembly for Easy Service Access. Tubular Aluminized Steel Primary Heat Exchanger. High-Level Self-Diagnostic Controls With Fault Codes. Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal. Fully-Gasketed, Independent Access Doors With View Ports. External Air Filters (Not Included) Provide Flexibility for IAQ Needs. Patent-Pending Condensate Management System Eliminates the Need for External Condensate Traps. All Models Are Propane Convertible.
TM8X/TMLX
TM8X/TMLX Model: TM8X/TMLX Capacities: 60 - 120 Input MBH 80% AFUE Warranty: Compressor - NA Heat Exchanger - 20 Years Other parts - 10-Year Limited* 80% AFUE Single Stage Multi-Position ECM Gas Furnaces These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Low unit amp requirement for easy replacement application. All models are convertable to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 5 speed direct drive, ECM high efficiency DC motor with blower off delay for lower electrical power usage and improved cooling SEER ratings. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger. Timed on, adjustable off blower capability for maximum comfort. Blower door safety switch. Solid removable bottom panel allows easy conversion. Low NOx models have been designed to meet specific code requirements. Airflow leakage less than 1% of total airflow at ductblaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney. 1/4 turn knobs provided for easy door removal. Insulated blower compartment for thermal and acoustic performance.
TM8T/TMLT
	TM8T/TMLT Model: TM8T/TMLT Capacities: 60 - 120 Input MBH 80% AFUE Warranty: Compressor - NA Heat Exchanger - 20 Years Other parts - 10 Year Limited * Two Stage PSC 80% Gas Furnace These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Blower-off delay for cooling SEER improvement. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Low unit amp requirement for easy replacement application. All models are convertable to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 4 speed direct drive, PSC motor. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger. Timed on, adjustable off blower capability for maximum comfort. Blower door safety switch. Solid removable bottom panel allows easy conversion. Low NOx models have been designed to meet specific code requirements. Airflow leakage less than 1% of total airflow at ductblaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney. 1/4 turn knobs provided for easy door removal. High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings. Insulated blower compartment for thermal and acoustic performance.
TM8V/TMLV
TM8V/TMLV Model: TM8V/TMLV Capacities: 60 - 120 Input MBH 80% AFUE Warranty: Compressor - NA Heat Exchanger - 20 Years Other parts - 10 Year Limited * Two Stage VS ECM 80% Multi-Position Gas Furnace These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Two stage heating operation includes two stage gas valve, two stage inducer operation and variable speed ECM blower operation. Adjustable delay timer allows two stage operation with a single stage thermostat. ECM variable speed drive for cooling SEER enhancement, improved comfort with optional airflow delay profiles, and continuous fan options for IAQ performance. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Low unit amp requirement for easy replacement application. All models are convertable to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger. Blower door safety switch. Solid removable bottom panel allows easy conversion. Airflow leakage less than 1% of total airflow at ductblaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet 2 stage inducer operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Venting applications - may be installed as a common vent with other gas-fired appliances or use of a masonry chimney. 1/4 turn knobs provided for easy door removal. Insulated blower compartment for thermal and acoustic performance. Low NOx models have been designed to meet specific code requirements.
TM9T
TM9T Model: TM9T Capacities: 60 - 120 Input MBH 96% AFUE Warranty: Compressor - NA Heat Exchanger - Lifetime Other parts - 10-Year Limited* Two Stage PSC 96% AFUE Multi-Position Gas Furnace These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and vent piping. Special Benefits Two stage heating operation includes two stage gas valve, two stage inducer operation and 4 speed, direct drive PSC motor blower operation. Adjustable delay timer allows two stage operation with a single stage thermostat. Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Blower-off delay for cooling SEER improvement. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code display. Low unit amp requirement for easy replacement application. All models are convertable to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger with stainless steel tube/aluminum fin secondary heat exchanger for outstanding efficiency. Solid removable bottom panel allows easy conversion. Airflow leakage less than 1% of nominal airflow at ductblaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Insulated blower compartment for thermal and acoustic performance. 1/4 turn knobs provided for easy independent door removal. Internal condensate trap design (patent pending) provides condensate management options, easy visual operation check, and is self priming to prevent nuisance problems. Protection included from air intake, exhaust vent or condensate blockage. Venting applications maybe installed as either 2 pipe sealed combustion or single pipe vent using indoor combustion air.
TM9V
TM9V Model: TM9V Capacities: 40 -120 Input MBH 96% AFUE Warranty: Compressor - NA Heat Exchanger - Lifetime Other parts - 10-Year Limited* Meets or Exceeds ENERGY STAR Compliance 96% 2 Stage VS Multi-Position Gas Furnace These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category IV listed and may be vented either through side wall or roof applications using approved plastic combustion air and venr piping. Special Benefits Two stage heating operation includes two stage gas valve, two stage inducer operation and variable speed ECM blower operation. Adjustable delay timer allows two stage operation with a single stage thermostat. Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. ECM variable speed drive for cooling SEER enhancement, improved comfort with optional airflow delay profiles, and continuous fan options for IAQ performance. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code display. Low unit amp requirement for easy replacement application. All models are convertable to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger with stainless steel tube/aluminum fin secondary heat exchanger for outstanding efficiency. Solid removable bottom panel allows easy conversion. Airflow leakage less than 1% of nominal airflow for ductblaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer operation, burner, and blower operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Insulated blower compartment for thermal and acoustic performance. 1/4 turn knobs provided for easy independent door removal. Internal condensate trap design (patent pending) provides condensate management options, easy visual operation check, and is self priming to prevent nuisance problems. Protection included from air intake, exhaust vent or condensate blockage. Venting applications maybe installed as either 2 pipe sealed combustion or single pipe vent using indoor combustion air.
TM9M
TM9M Model: TM9M Capacities: 60 - 120 Input MBH 97% AFUE Warranty: Compressor - NA Heat Exchanger - Lifetime Other parts - 10-Year Limited* 97% AFUE Modulating PSC Multi-Position Gas Furnace These TM9M compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. Modulating heating operation (100 stages)with PSC motor acting like a variable speed ECM in heating mode provides outstanding efficiency and comfort. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. Designed and certified as Category IV furnaces, these TM9M models may be installed as direct vent systems through side wall or roof applications using approved plastic combustion air and vent materials. Special Benefits "100 stage" Modulating PSC furnace design. 2nd generation Modulating Control . White Rodgers 36J27 Gas Valve does not require change out for LP applications. Compact 33” Height and Standard Cabinet Widths. Multi-Position Design With Minimal Conversion Requirements. Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1” ESP. 4 Speed PSC Motor with Large, Quiet Blower. Fully-Supported, Slide-Out Blower Assembly for Easy Service Access. Tubular Aluminized Steel Primary Heat Exchanger. High-Level Self-Diagnostic Controls With Fault Codes. Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal. Fully-Gasketed, Independent Access Doors With View Ports. External Air Filters (Not Included) Provide Flexibility for IAQ Needs. All Models Are Propane Convertible. Lo-Nox Models Meet Specific Code Requirements.
TM8Y
TM8Y Model: TM8Y Capacities: 60 - 120 Input MBH 80% AFUE Warranty: Compressor - NA Heat Exchanger - 20 Years Other parts - 10 Year Limited * Two Stage STD ECM 80% Gas Furnace These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications. These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation. These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code. Special Benefits Easily applied in upflow, horizontal left or right, or downflow installation with minimal conversion necessary. Compact, easy to install, ideal height 33" tall cabinet. Blower-off delay for cooling SEER improvement. Easy access to controls to connect power/control wiring. Built-in, high level self diagnostics with fault code displays standard on integrated control module for reliable operation. Low unit amp requirement for easy replacement application. All models are convertable to use propane (LP) gas. Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability. 100% shut off main gas valve for extra safety. 24V, 40 VA control transformer and blower relay supplied for add-on cooling. Hi-tech tubular aluminized steel primary heat exchanger. Timed on, adjustable off blower capability for maximum comfort. Blower door safety switch. Solid removable bottom panel allows easy conversion. Low NOx models have been designed to meet specific code requirements. Airflow leakage less than 1% of total airflow at ductblaster conditions. No knockouts to deal with, making installation easier. Movable duct connector flanges for application flexibility. Quiet inducer operation. Inducer rotates for easy conversion of venting options. Fully supported blower assembly for easy access and removal of blower. External air filters used for maximum flexibility in meeting customers IAQ needs. Venting applications - may be installed as a common vent with other gas-fired appliances or use a masonry chimney. 1/4 turn knobs provided for easy door removal. High-efficiency blower motor for lower electrical power usage and improved A/C SEER ratings. Insulated blower compartment for thermal and acoustic performance.
1/2         First page   Reverse page   Next page    last page  
Website designed by : maplesystems.ca
Show Room Add:589 Middlefield Rd, Unit 25, Scarborough(North of Finch), M1V 4Y6
CANA AIR COOLING AND HEATING LTD is committed to respecting the privacy of individuals and recognizes a need for the appropriate management and protection of any personal information that you agree to provide to us. We will not share your information with any third party outside of our organisation, other than necessary to fulfill your request.